The Structure And Magnetic Properties Of Fe0.50cr0.50-Xsix (X=0-0.1) Nano Materials Prepared Via Mechanical Alloying Technique

Kontan Tarigan

Abstract


The main objective of this study is the investigation of the relationship between the structure and the magnetic properties of Fe50Cr50-xSix (x=0-0.1) metastable alloys which were made by mechanical alloying for 36 hours. Research in this field feels still lacking. To understand the structure using by X-ray diffraction (XRD) and the magnetic properties are measured by using a Physical Property Measurement System (PPMS). The result with variable of x = 0-, 0.025-, 0.050-, 0.075- and 0.1 wt. %. are crystallite sizes (D) increase from 7 to 8.5 nm, the structural strains (ϵ) are down about 20% from normal circumstances. The grain sizes increase causing the number of domains to increase then the mobility of domain decreases or coercivity (Hc) decreases from 120 to 40 Oe. In amorphous state coercivity rises and crystallite sizes decrease, suddenly.


Keywords


Fe0.50Cr1-0.50Six nanocrystalline and amorphous alloys, structural and magnetic properties

Full Text:

PDF

References


. R. Hasegawa, Present status of amorphous soft magnetic alloys, Journal of Magnetism and Magnetic Materials 215–216 (2000) 240-245.

. Michael E. McHenry, Matthew A. Willard, David E. Laughlin, Amorphous and nanocrystalline materials for applications as soft magnets, Progress in Materials Science 44 (1999) 291-433.

. Shiddartha Paul, et al, A Modified Embedded-Atom Potential for Fe-Cr-Si Alloys, J. Phys. Chem. C 2021, 125, 41, 22863–22871,

. K. Idczak and R. Idczak, Investigation of Surface Segregation in Fe-Cr-Si Alloys by XPS, Metallurgical and Materials Transactions A volume 51, pages3076–3089 (2020)

. Ran Guang et. al., Formation of nanocrystalline and amorphous phase of Al–Pb–Si–Sn–Cu powder during mechanical alloying, Materials Science and Engineering A 416 (2006) 45–50.

. Yifang Ouyang, Hongmei Chen, Xiaping Zhong, Yong Du, amorphous alloys prepared by mechanical alloying, Physica B 391 (2007) 380–384.

. P. Kameli, H. Salamati, and A. Aezami, Effect of particle size on the structural and magnetic properties of Journal of Applied Physics 100, 053914 (2006).

. C. Suryanarayana, Mechanical alloying and milling, Progress in Materials Science 46 (2001) 1-184.

. J. J. Ipus, et. al., Structure and magnetic properties of Fe-Nb-B amorphous/nanocrystalline alloys produced by compaction of mechanically alloyed powders, Journal of Applied Physics 107, 073901(2010).

.Ammouchi Nesrine, et al., Structural, Microstructural and Magnetic Characterizations of Mechanically Alloyed Fe65Si20Cr15 Powders Mixture, Journal of Superconductivity and Novel Magnetism 28(12), September 2015, DOI: 10.1007/s10948-015-3203-6

.Charles Kittel, Introduction to Solid State Physics (eight edition), John Wiley & Sons (2005) 575-577.

. K. Tarigan, D. Sebayang, S. C. Yu, and D. S. Yang, Local Structure and Magnetic Properties of Fe50Cr40Si10 Nanocrystalline Alloys, IOP Conf. Series: Materials Science and Engineering 343 (2018), 343 012008

. K. Tarigan et al., Local Ordering Study of Nanostructure FeMnAl Alloys, IEEE Trans. Magn., 45 (6) (2009), ISSN: 0018-9464, p. 3492-3495.

.K. Tarigan, et al., Structural and Magnetic Properties of Fe50Al50 Nanocrystalline Alloys, Journal of the Korean Physical Society, Vol. 57, No. 61, (December 2010), ISSN: 1976-8524, p. 1555-1558.

.K. Tarigan et al., Structural and magnetic properties of Ni45Al45C10 nanocrystalline alloys, IEEE Trans. Magn.,46(2), ISSN: 0018-4964, p. 377-379 (2010).

.K. Tarigan et al., Local Structure and Magnetic Properties of Fe-Mn Nano crystalline Alloys Fabricated by Me- chanical Alloying Technique as a Function of Milling Time, Journal of Magnetics 18(1), ISSN: 1226-1750, p. 1-4 (2013).




DOI: http://dx.doi.org/10.52155/ijpsat.v33.1.4401

Refbacks

  • There are currently no refbacks.


Copyright (c) 2022 Kontan Tarigan

Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.